Schedule Your Job Now

 

This great article down below relating to How to Install a Bathtub is truly intriguing. Check it out yourself and figure out what you think of it.

Mounting a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old tub with a brand-new one is additionally a moderately hard task. If the old bathtub is readily easily accessible, the project can move speedily; if you need to open up a wall to get rid of the old tub and place the new bath tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require an assistant to vacate the old bathtub and set in the new one. Make sure you have qualified yourself for the task and also fit trying it. As opposed to employing a service provider to take over a halfway-completed project, it is far better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you mount a brand-new bathtub in your bathroom if you have actually already purchased a brand-new tub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and material list must comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, turn on the faucets to drain any water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place in between the faucet and also the sink. Protect the faucet in place with the supplier provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Mounting the Tub

Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leaks and also tighten them if required. Load the tub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Lastly, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub needs to wait till the bathtub has been used at least when as this will certainly settle it right into its last position.

 

 

Planning for the Installation

First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final setting.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill the tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you appreciate reading up on Installing A Bathtub? Leave a remark directly below. We'd be interested to listen to your thinking about this piece. In hopes to see you back again soon. For those who appreciated our page if you please make sure you remember to pass it around. We value reading our article about Tools You Need to Install a New Bathtub .

Emergency plumber? One call away.